Plumbing Basics: Your Key to Bathtub Installation
Plumbing Basics: Your Key to Bathtub Installation
Blog Article
The article down below on the subject of Tools You Need to Install a New Bathtub is especially engaging. Don't miss it.
Mounting a tub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old tub is conveniently obtainable, the job can move immediately; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will require an assistant to leave the old bathtub as well as set in the brand-new one. Make certain you have actually certified on your own for the job as well as are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed task, it is much better to take into consideration using one before you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly aid you install a brand-new tub in your washroom if you have currently purchased a new tub as well as don't need to transform the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist ought to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the restricted gain access to that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and also the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type needs to be attached to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Using both wooden boards under its feet, put the tub in the needed setting. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the bathtub till the spirit level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Turn on the water supply as well as check all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and also inspect the overflow outlet and the typical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has actually been made use of at the very least when as this will resolve it right into its final setting.
Planning for the Setup
Firstly, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final position.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, creating the water to permeate the wall between the bathroom and also the tiling, bring about complications with wetness as well as feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is suggested to fit the floor tiles using water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write a remark directly below. We'd be pleased to hear your ideas about this blog. Hoping that you come back again in the future. Make sure you take a moment to distribute this post if you appreciated it. Many thanks for your time. Come back soon.
Drips? Dial fast! Report this page